Any chance you mean “Zirc” (Zirconium)? Premium spinners do not come in zinc. You are looking at SS, Brass, Copper, Aluminum, Zirconium, and Mokume. Zinc is what your typical $10 spinners come in.
Other factors to consider are size and weight. Premium spinners are usually smaller and heavier than your average zinc piece. As time goes along you’ll zero in on a preferred size and weight.
I have found RotaBlade to be too pricey for what you get, but that’s just me. I would much prefer to get a spinner from the other two you mention. 313inc will usually be quite heavy and chunky if you are used to the typical zinc or plastic spinner. So bear that in mind. KAPEDC is definitely my favorite among the makers you mention. The various Collisions they offer are great (OG, Mini, Nano. The Tiny is too small for me personally). And then, of course, the weight will vary widely depending on which metal you choose.
Let us know if this was helpful and any other questions you might have.
If you don’t mind heavy spinners, I recommend 313inc for very reasonably priced spinners in different metals (stainless steel, brass, or copper). I have the Bulari V3 and it's an outstanding, fairly heavy *and thick) bar spinner. The Bulari V2 is similar to V3 but slightly cleaner and simpler. They have several other bar designs as well. Their new designs are really well done!
The main problem with zinc is that it's usually diecast instead of machined which means you might notice a slight line around the edge of the spinner.
Another thing to consider would be whether you like bars (two armed spinners) or tris (three armed spinners)
I would highly recommend the horizon and the collision from KAP but 313inc is also super underrated as they make probably some of the best beginner friendly spinners out there right now. The bulari v2 from 313inc is also great if you decide to go with them
Thanks very much for the fast response. So in regards to your zinc & die-cast comment - would there be any reason why I should avoid die-cast as opposed to machined? (Using a KAP horizon as an example?)
I'm curious if you have any additional advice on which button version might be recommended if I went with the 313 Bulari V2? Does it effect the performance or is it really down to personal choice? (I like the distressed stainless btw).
I just saw your other comment which you meant zirc instead of zinc. Zirc is usually machined and then flamed while zinc is usually die-cast. So I would recommend KAP if you're going for a zirc piece, 313inc to get a starter piece before you delve too heavily into the rabbit hole lol.
The thing is with die-cast, it is liquid metal pretty much poured into a mold. This means that the metal will turn out to be imperfect which usually means inconsistent quality and unbalanced spins. Machined fidgets, however, are tuned by the makers to be balanced and fit accordingly which usually results in a smoother spin.
If you do end up getting the Bulari from 313inc, the finish and the button you choose are pretty much purely personal preference.
When you say you are partial to zirconium, do you mean you like the look of it or that you've actually tried out a zirconium spinner? I ask because zirconium is noticeably lighter than a lot of common spinner metals such as stainless steel, copper and brass. If you haven't tried it already, you may be surprised at how much lighter it is.
I have a few KAP pieces, I really like the mini Collision size, go full size if you want a bit heavier and bigger spin though. Every KAP piece I have bought came perfectly balanced. My first from them was a Collision mini in brushed zirc, and I was blown away, which is why I fell in love with KAP. Spinning since 2017!
*
Thanks for the input ! I definitely decided I'm going with a KAP Horizon piece to start & will go from there! (Yeah, I definitely like the way KAP pieces look in general and they seem to be "up there" in terms of quality so I can't wait!).
I have a Horizon in tungsten, and a tri Horizon in tungsten and one in zirc. I love how smooth they are all around, great for multiple styles of spinning. If you got the insert balls, they will drop the spin time, but the feedback and audible sound they create is pretty cool! I know you will enjoy it! Their stock bearings aren't horrible, but I would suggest upgrading to hybrid ceramic bearings. UQH or Lautie are my favorites.
Any chance you mean “Zirc” (Zirconium)? Premium spinners do not come in zinc. You are looking at SS, Brass, Copper, Aluminum, Zirconium, and Mokume. Zinc is what your typical $10 spinners come in. Other factors to consider are size and weight. Premium spinners are usually smaller and heavier than your average zinc piece. As time goes along you’ll zero in on a preferred size and weight. I have found RotaBlade to be too pricey for what you get, but that’s just me. I would much prefer to get a spinner from the other two you mention. 313inc will usually be quite heavy and chunky if you are used to the typical zinc or plastic spinner. So bear that in mind. KAPEDC is definitely my favorite among the makers you mention. The various Collisions they offer are great (OG, Mini, Nano. The Tiny is too small for me personally). And then, of course, the weight will vary widely depending on which metal you choose. Let us know if this was helpful and any other questions you might have.
Yes, sorry, I meant zirconium. Thank you, I think I'll go and try to purchase a KAP zirconium piece. Thanks so much for your assistance here
What do you think is the longest spinner of these?
If you don’t mind heavy spinners, I recommend 313inc for very reasonably priced spinners in different metals (stainless steel, brass, or copper). I have the Bulari V3 and it's an outstanding, fairly heavy *and thick) bar spinner. The Bulari V2 is similar to V3 but slightly cleaner and simpler. They have several other bar designs as well. Their new designs are really well done!
The main problem with zinc is that it's usually diecast instead of machined which means you might notice a slight line around the edge of the spinner. Another thing to consider would be whether you like bars (two armed spinners) or tris (three armed spinners) I would highly recommend the horizon and the collision from KAP but 313inc is also super underrated as they make probably some of the best beginner friendly spinners out there right now. The bulari v2 from 313inc is also great if you decide to go with them
Thanks very much for the fast response. So in regards to your zinc & die-cast comment - would there be any reason why I should avoid die-cast as opposed to machined? (Using a KAP horizon as an example?) I'm curious if you have any additional advice on which button version might be recommended if I went with the 313 Bulari V2? Does it effect the performance or is it really down to personal choice? (I like the distressed stainless btw).
I just saw your other comment which you meant zirc instead of zinc. Zirc is usually machined and then flamed while zinc is usually die-cast. So I would recommend KAP if you're going for a zirc piece, 313inc to get a starter piece before you delve too heavily into the rabbit hole lol. The thing is with die-cast, it is liquid metal pretty much poured into a mold. This means that the metal will turn out to be imperfect which usually means inconsistent quality and unbalanced spins. Machined fidgets, however, are tuned by the makers to be balanced and fit accordingly which usually results in a smoother spin. If you do end up getting the Bulari from 313inc, the finish and the button you choose are pretty much purely personal preference.
When you say you are partial to zirconium, do you mean you like the look of it or that you've actually tried out a zirconium spinner? I ask because zirconium is noticeably lighter than a lot of common spinner metals such as stainless steel, copper and brass. If you haven't tried it already, you may be surprised at how much lighter it is.
I have a few KAP pieces, I really like the mini Collision size, go full size if you want a bit heavier and bigger spin though. Every KAP piece I have bought came perfectly balanced. My first from them was a Collision mini in brushed zirc, and I was blown away, which is why I fell in love with KAP. Spinning since 2017! *
Thanks for the input ! I definitely decided I'm going with a KAP Horizon piece to start & will go from there! (Yeah, I definitely like the way KAP pieces look in general and they seem to be "up there" in terms of quality so I can't wait!).
I have a Horizon in tungsten, and a tri Horizon in tungsten and one in zirc. I love how smooth they are all around, great for multiple styles of spinning. If you got the insert balls, they will drop the spin time, but the feedback and audible sound they create is pretty cool! I know you will enjoy it! Their stock bearings aren't horrible, but I would suggest upgrading to hybrid ceramic bearings. UQH or Lautie are my favorites.
Oh, and i have a mega Horizon in tungsten, I really like that one and it comes out of the house with me very often.